Evaluation of brittle crack arrest toughness for highly-irradiated reactor pressure vessel steels

Iwata, Keiko; Hata, Kuniki; Tobita, Toru; Hirota, Takatoshi*; Takamizawa, Hisashi; Chimi, Yasuhiro; Nishiyama, Yutaka

Proceedings of ASME 2021 Pressure Vessels and Piping Conference (PVP 2021) (Internet), 7 Pages, 2021/07

Evaluation of impact with high temperature engineering test reactor using realistic model of stack and reactor building

Ono, Masato; Fujiwara, Yusuke; Matsumoto, Tetsuro*; Iigaki, Kazuhiko

Nihon Genshiryoku Gakkai Wabun Rombunshi, 19(2), p.110 - 120, 2020/06

https://doi.org/10.3327/taesj.J19.005

Integrity confirmation for buildings against collisions of projectiles has been conducted to evaluate collisions between a projectile with simple shape and a wall using empirical formulas. It is a matter of fact, there is a possibility that structures with complex shape such as stack may collide with a reactor building. However, there were not so many studies of collisions between structures with complex shape and buildings in the literature. Impact evaluation was carried out using reactor building and stack with real shape and adequate physical property. It was found that ceiling of reactor building was not damaged by the collision, confirming that there was no effect inside of reactor building.

Progress of neutron-capture cross-section measurements promoted by ImPACT project at ANNRI in MLF of J-PARC

Nakamura, Shoji; Kimura, Atsushi; Hales, B. P.; Iwamoto, Osamu; Shibahara, Yuji*; Uehara, Akihiro*; Fujii, Toshiyuki*

JAEA-Conf 2018-001, p.199 - 203, 2018/12

https://doi.org/10.11484/jaea-conf-2018-001

Study on cross-section measurements has been promoted for Cs among long-lived fission products in ImPACT Project. The feasibility study on Se sample preparation also has been conducted to measure its cross sections in future. During the feasibility study, we started the neutron-capture cross-section measurements of stable Se isotopes. This paper reports research progresses on preparation of a radioactive Cs sample, neutron irradiation experiments with the Cs sample, and cross-section measurements of stable Se isotopes.

Research on neutron capture cross sections at J-PARC in ImPACT Project

Nakamura, Shoji; Kimura, Atsushi; Hales, B. P.; Iwamoto, Osamu; Tsubata, Yasuhiro; Matsumura, Tatsuro; Shibahara, Yuji*; Uehara, Akihiro*; Fujii, Toshiyuki*

JAEA-Conf 2017-001, p.15 - 22, 2018/01

https://doi.org/10.11484/jaea-conf-2017-001

Neutron nuclear data of long lived fission products (LLFPs) have been required as basic data for the technology of reduce environmental impact involved in high level radioactive wastes (HLW). The innovative large project called by "Impusing Paradigm Change through Disruptive Technologies Program: ImPACT" have been started from October, 2014. In the ImPACT project, some research groups of JAEA engaged in the Project No.2 (Nuclear Reaction Data Measurements), and have started measurements of neutron capture cross-section at J-PARC/MLF/ANNRI. In our research, we selected cesium-135 (Cs) nuclide (half life: 2.310 yr.) among LLFPs in the HLW, and decided to measure the neutron capture cross-sections of Cs. When measurement, the Cs sample might contained cecium-137 (Cs) as impurities because it's impossible to chemically separate each other. To measure the cross-sections of Cs, there should be also needed to know the cross-sections of Cs. In this work, sample maintenance also has been examined especially for selen-79 (Se) nuclide among LLFPs having difficulty in sample preparations. In this oral session, the outline of our research project will be presented together with a research motivation, situations of past reported data, total schedules, progress, future plans, and some of high light data for neutron capture cross-section measurements.

Micro-impact damage caused by mercury bubble collapse

Futakawa, Masatoshi; Naoe, Takashi*; Kogawa, Hiroyuki; Date, Hidefumi*; Ikeda, Yujiro

JSME International Journal, Series A, 48(4), p.234 - 239, 2005/10

Mercury target will be installed at the material science and life facility in J-PARC, which will promote innovative science. The mercury target will be subjected to the pressure wave caused by proton bombarding in the mercury. The pressure wave propagation induces the cavitation in mercury that imposes localized impact damage on the target vessel. The impact erosion is a critical issue to decide the lifetime of target. An electromagnetic impact testing machine, MIMTM, was developed to reproduce the localized impact erosion damage and evaluate the damage formation. Additionally, droplet impact analyses were carried out to investigate the correlation between isolate pit profile and micro-jet velocity. We confirmed that the value of depth/radius was applicable to estimate micro-jet velocity, and the velocity at 560 W in MIMTM equivalent to 1MW proton beam injection was 300 m/s approximately.

On the requirement for remodelling the spent nuclear fuel transportation casks for research reactors; A Review of the drop impact analyses of JRC-80Y-20T

Review Group on the Structure of the Spent Nuclear Fuel Transportation Casks for

JAERI-Review 2005-023, 133 Pages, 2005/07

JAERI-Review-2005-023.pdf:18.88MB

The Japan Atomic Energy Research Institute (JAERI) constructed two stainless steel transportation casks, JRC-80Y-20T, for spent nuclear fuels of research reactors and had utilized them for transportation since 1981. A modification of the design was applied to the USA for transportation of silicide fuels. Additional analyses employing the impact analysis code LS-DYNA that was often used for safety analysis were submitted by the JAERI to the USA to show integrity of the packages; the casks were still not approved, because inelastic deformation was occurred on the surface of the lid touching to the body. To resolve this problem on design approval of transportation casks, a review group was formed at the end of this June. The group examined the impact analyses by reviewing the input data and performing the sensitivity analyses. As the drop impact analyses were found to be practically reasonable, it was concluded that the approval of the USA for the transportation casks could not be obtained just by revising the analyses; therefore, remodelling the casks is required.

Correlation between cleavage fracture toughness and charpy impact properties in the transition temperature range of reactor pressure vessel steels

Onizawa, Kunio; Suzuki, Masahide

JSME International Journal, Series A, 47(3), p.479 - 485, 2004/07

In the structural integrity assessment of reactor pressure vessel, fracture toughness values are estimated by assuming that the radiation effect on fracture toughness is equivalent to that on Charpy properties. Therefore, it is necessary to establish the correlation between both properties especially on irradiation embrittlement. In this paper, we present the fracture toughness data obtained by applying the master curve approach that was adopted recently in the ASTM test method. Materials used in this study are five ASTM A533B class 1 steels and one weld metal. Neutron irradiation for Charpy-size specimens as well as standard Charpy-v specimens was carried out at the Japan Materials Testing Reactor. The shifts of the reference temperature on fracture toughness due to neutron irradiation are evaluated. Correlation between the fracture toughness reference temperature and Charpy transition temperature is established. Based on the correlation, the optimum test temperature for fracture toughness testing and the method to determine a lower bound fracture toughness curve are discussed.

Pitting damage formation up to over 10 million cycles; Off-line test by MIMTM

Futakawa, Masatoshi; Naoe, Takashi; Kogawa, Hiroyuki; Tsai, C.-C.*; Ikeda, Yujiro

Journal of Nuclear Science and Technology, 40(11), p.895 - 904, 2003/11

https://doi.org/10.3327/jnst.40.895

A liquid-mercury target system for the MW-scale target is being developed in the world. The pitting damage induced by pressure wave propagation gets to be one of critical issues to estimate the life of the target structure with mercury and to evaluate its structural integrity. The off-line test on the pitting damage at high cycles over 10 millions was carried out using a novel device, the MIMTM which drives electromagnetically to impose pulse pressure into the mercury. It was found that from the pitting damage data obtained by the MIMTM that the pitting damage can be characterized in two steps, an incubation period that can extend to more than 106 cycles in 316SS and 107 cycles in surface hardening treated one and steady state erosion where mass loss scales with the number of cycles to approximately the 1.27 power for mercury. The length of the incubation period is primarily a function of the material and the intensity of the pressure. This observation provides a simple model for estimating lifetime for different materials and beam power.

8-oxoguanine lesioned B-DNA molecule complexed with repair enzyme hOGG1; A Molecular dynamics study

Pinak, M.

Journal of Computational Chemistry, 24(7), p.898 - 907, 2003/04

https://doi.org/10.1002/jcc.10248

The molecular dynamics (MD) simulation of DNA mutagenic oxidative lesion 8-oxoG, complexed with the repair enzyme - hOGG1 was performed in order to describe the dynamical process of DNA-enzyme complex formation. After 500 picoseconds of MD the lesioned DNA and enzyme formed a complex that lasted stable until the simulation was terminated at 1 ns. The N-terminus of arginine 313 was located close to the phosphodiester bond of nucleotide with 8-oxoG enabling chemical reactions between amino acid and lesion. Phosphodiester bond at C5' of 8-oxoG was displaced to the position close to the N-terminus of arginine 313. The water mediated hydrogen bonds network was formed in each contact area between DNA and enzyme further enhancing the stability of complex.

Erosion damage on solid boundaries in contact with liquid metals by impulsive pressure injection

Futakawa, Masatoshi; Kogawa, Hiroyuki; Hino, Ryutaro; Date, Hidefumi*; Takeishi, Hiromasa*

International Journal of Impact Engineering, 28(2), p.123 - 135, 2003/02

https://doi.org/10.1016/S0734-743X(02)00054-4

JAERI is carrying out research & development to construct the a of spallation neutron source facility, which may bring us innovative science fields. A high power proton beam will be injected into a liquid mercury target to produce neutrons. The mercury vessel will consequently be subjected to the pressure waves generated by rapid thermal expansion. The pressure waves will propagate from the liquid mercury into the vessel solid metal, and back again. The pressure waves may induce erosion at the interface between the solid metal vessel and the liquid mercury under certain loading conditions, e.g. impact. In order to investigate the impact erosion damage due to the pressure wave, we have carried out impact experiments using a modified conventional split Hopkinson pressure bar apparatus on mercury filling a small chamber. Surface degradation in the form of many pits was observed and the ranking order of damage was found to be A6061316SS@Inconel600Maraging steel, which is the same as that of hardness.